Begining my work on the alternator(generator)

Using the pulse motor, I am making an alternator similar to a homemade windmill alternator. Magnets on a steel plate(to increase the magnetic field) rotating N S N S N S 6 pole n45 2"x1"x1/14" around the stator consisting of 6 coils wired in parallel (inside to inside and outside to outside)I can't wait for my magnets to arrive. [ voir sur Youtube.com ]

Durée : 4 min 17
En ligne le : 12/01/08 20:46
Envoyer cette vidéo par Gmail

Vidéos (12) | Aucun article de blog

-> Plus de vidéos sur le site Youtube.com :

stumbled onto part three

shows the pulsed hho cell produceing voltage by putting the - of the cell through a cap to one side of the coil and the other side of the coil goes back to the +,that creates amagnetic pulse, the other coil (bifilar) acts as a generator collecting the magnetic pulses. rember rate or comment its my only pay. [ voir sur Youtube.com ]

Durée : 3 min 06
En ligne le : 29/02/08 12:46
Envoyer cette vidéo par Gmail

Haut de page

001 - Winding coils for my first project

The concept of overunity produced by coil pulse generators is a very interesting field of research ,so I decided to try out some design of my own for a generator that could work using that concept giving me the chance of tryng different setups between the coils and the magnets in the attempt of achieving overunity. This video shows an easy and quick way to wind coils using an electronic drill/screwdriver . [ voir sur Youtube.com ]

Durée : 4 min 06
En ligne le : 27/11/07 00:40
Envoyer cette vidéo par Gmail

Haut de page

Moving forward with the Resin

I encased the magnets and coil to the resin. It only took 2 hours to set. I found other resin at lowes, it flows MUCH better than the jelly stuff at autozone. And Elmers Glue makes it "a name you can trust" hehe Thanks for watching. [ voir sur Youtube.com ]

Durée : 2 min 31
En ligne le : 18/01/08 19:39
Envoyer cette vidéo par Gmail

Haut de page

002 - selfmade magnetic or mechanic switch

The video shows the way to easily make out of a shaving razor blade, a small switch that can be activated either mechanically or magnetically to be used in coil pulse generator units as a cheap , quick and easy to build substitute of reed switches [ voir sur Youtube.com ]

Durée : 7 min 29
En ligne le : 30/11/07 05:51
Envoyer cette vidéo par Gmail

Haut de page

Pulse Motor (New 4 Coil HD Idea) 018

I will get a torc drive set tommorrow and Build this. I can put the top back on the HD once assembled to make sure the magnets do no kill me....lol The one in the last video shed its Magnets at high speed and splatted them up the walls, be warned if you are reproducing these videos...... [ voir sur Youtube.com ]

Durée : 1 min 23
En ligne le : 10/09/07 23:21
Envoyer cette vidéo par Gmail

Haut de page

True RMS analog amp meter

Sorry about the video quality and the gradient on the amp meter. I have just ordered another amp meter which will show the needle moving more i.e 2amp meter. [ voir sur Youtube.com ]

Durée : 10 min 01
En ligne le : 09/02/08 00:33
Envoyer cette vidéo par Gmail

Haut de page

Pulse Motor (Power Out Idea) 017

I am going to build another motor around this HD that will output voltage as seen and also Collect the Back EMF. I have built a 3 coil system that I will hook to some electronics [ voir sur Youtube.com ]