1-4 Cell Lipo Voltage meter
Voltage meter for 1-4 Cell LiPo packs [ go to Youtube.com ]
Time
: 0 min
21
Added
: 24/11/07 20:39
Send with Gmail
Videos
(120)
|
Blog posts
(43)
DD Audio new setup Voltage Meter
Just showing off the new Tsunami Voltage meter! [
go to Youtube.com
]
Time
: 0 min
41
Added
: 20/09/07 09:48
Send with Gmail
Korg Synthesizer MS-10 Pitch Bend Repair
http://www.aztechmusic.com
Gary explains the voltages present on the pitch bend pot and how to determine it is working correctly. Use of a volt ohm meter is explained in the process. [
go to Youtube.com
]
Time
: 5 min
51
Added
: 03/03/08 21:19
Send with Gmail
volt meter
regreee [
go to Youtube.com
]
Time
: 0 min
40
Added
: 07/12/06 09:43
Send with Gmail
Aurora rc plane electric -Quebec C2VM - 33.6 Volts (8s lipo)
Aurora rc plane airplane with a Hyperion 4045-10
motor, 8S Lipo 3700 (33.6Volts!),
APC 13X13 pattern prop,
68 amps,
12S 100amps ESC
7 servos!! (Retracts Graupner C2003+ HS 81, 2X ailerons HS85mg, rudder
Graupner 4042, Elevator 2X H125mg)
5X GP2000 + voltmeter pour la réception
Weight: 3.85 kg
Speed 180-200km/h [
go to Youtube.com
]
Time
: 7 min
06
Added
: 02/08/07 05:13
Send with Gmail
the homebrew Band Scope Part 1
The Homebrew 40m Band Scope or a much narrow version of the Spectrum analyzer. it is direct conversion, Used LM555 to produce sawtooth and FM the tuning diode with sawtooth. Connected to X axis is the Sawooth voltage, and the Y axis is then connected to the product detector. [
go to Youtube.com
]
Time
: 1 min
04
Added
: 03/11/06 08:40
Send with Gmail
All About Circuit Bending and Equipment : Volt Meter & Equipment for Circuit Bending
Learn about volt meters with expert tips and advice on circuit bending equipment in this free video clip on noise music. [
go to Youtube.com
]
Time
: 2 min
19
Added
: 17/02/08 06:01
Send with Gmail
Russian VFD-VU meter
I bought a bunch of them at eBay. They all need some work, there is one FET missing. I did not have a KP303B so I used a BF256C. The FET forms a constant current source that defines the 0-point of the vu meter. I think a BF245 would do also ... The spec sheet says that you need 6.3V AC current for heating of the VFD. I used a 5V DC and it works well. Besides the 5V you need +-15V dc regulated for the opamps and the logic chips. The +15V is also used for anode voltage of the VFD tube. [
go to Youtube.com
]
Time
: 0 min
39
Added
: 14/01/08 21:10
Send with Gmail
Bypassing your Stereo: Hooking an MP3 player to your Car
My radio was not working, but I wanted to listen to my Mp3 player in my car - so I set up a switch, an amp, and a headphone wire. [
go to Youtube.com
]
Time
: 2 min
52
Added
: 15/02/08 23:36
Send with Gmail
Electric Motor
Simple Electric motor made of two paper clips a 1.5 volt dbl A battery and a meter of used alternator wire [
go to Youtube.com
]
Time
: 0 min
18
Added
: 21/05/07 02:04
Send with Gmail
1 -
10
of
120
Videos
Page:
First
| <
Preceding
|
Next
>
0
|
1
|
2
